RallyWerks
AMPS Nav Mount
Adventure Raid Mounting Solution
Mount AMPS pattern devices in addtion to a RallyComp, ICO, or RNS Unit for a seamless electronic Roadbook or Navigation setup utilizing a phone such as the rugged Samsung XCover Pro.
4 possible AMPS pattern positions for dual vertical or Single horizontal. Available in multiple colors to allow for a more customized fit.
Designed to mount directly to a 12mm tube or can be mounted utilizing one of the AMPS Pattern mounting positions. Shown mounted to a 2024 BMW F900GS with Navigation prep.
RallyLite Mount
RallyLite Mounting Solution
Designed to be mounted utilizing AMPS pattern tablet mounts.
Pictured here utilizing the Gamber Johnson Galaxy Tab Active powered mount. Which is all bolted to the MotoMinded Stout Mount.
This setup allows you to run both a tablet and a navigation device such as a RallyComp, ICO, or RNS unit.
Windscreen Spacers
Clearance Solution for Hand Guards
The Problem:
When you add hand guards or low sweep handle bars to many adventure bikes there is a chance of impacting the windscreen at full lock.
The Solution:
Install the windscreen spacer kit to allow additional clearance. Kit comes with 2 sets of 4 spacers, 4mm and 2mm thick. Recommended to use the least amount possible. Longer hardware may be needed.
*Shown installed on a 2024 BMW F900GS fitted with Fast Company Flexx Bars.
*Note: Bar position, and hand guard styles vary, these spacers may only help but not be the total solution. Check for proper fitment and installation when installing this or any accessory, we are not responsible for damages to components.
Contents:
4- 5mm ID x 4mm Thick
4- 5mm ID x 4mm Thick
RallyComp Template
Template tool for wire and mounting clearance.
Utilized to determine clearance for cables and devices. It works for ICO and RNS devices in addition to RallyComp.
The Problem:
Showing up to an event utilizing a RallyComp for scoring or navigation and not having enough clearance for the devices' cables.
The Solution:
This template allows you to mark off and cut/file/shave the needed area for proper cable clearance, saving time during scrutineering or inspection.
Note:
The cable window should be placed on the right side, and a slot should be added to allow the cable to enter.
MotoMinded
Stout Mount for Flexx Bars
by MotoMinded
Enhance your adventure with the STOUT MOUNT for Flex Bar, the ultimate universal GPS and phone mount designed for durability and convenience. It is perfectly compatible with the Trail Tech Voyager PRO (using a spacer) or any device featuring the AMPS bolt pattern. No drilling is required!
Fitments:
- Compatible with standard Flexx Bar or Flexx Bar Dual Sport by Fasst Co.
Features:
- Instantly mounts on top of Flex Bar upper linkage arms
- Compatible with all GPS mounts using the AMPS pattern
- Backed by a limited lifetime warranty
Pre-Assembled Kit Includes:
- Universal GPS Center Plate (1/4" Acetal plastic)
- Two hard plastic mounts with soft plastic clamping components
- Spacer for Trail Tech Voyager PRO or any GPS with a wide dock (+2 inches)
- Speed plate for quicker GPS dock mounting
Stout Mount
by MotoMinded
STOUT MOUNT - Universal GPS/Phone Mount
A highly adjustable and robust universal GPS/phone mount compatible with devices featuring the AMPS bolt pattern. It is available in two versions: 'Low Pro', which replaces top bar clamps, and 'Stacked', which bolts on top of OEM bar clamps.
Fitments:
Works exclusively with 1 1/8" (fat bars).
2002+ KTM All Models (OEM 90mm)
2015+ Husqvarna 125-701 cc (OEM 90mm)
2015+ Beta Small Enduro Bikes (OEM 90mm) Lo/Pro ONLY
2019+ Sherco (not trials) (OEM 90mm)
2018-2019 Honda CRF 450L (OEM 106mm)
2002+ Honda CRF450R (OEM 106mm)
2015+ Honda Africa Twin (OEM 100mm)
2019-2021 Yamaha T7 (OEM 100mm)
2019-2022 Yamaha YZ/WR (OEM 103mm)
2019-24 BMW 800-850 GS (OEM 96mm)
2019-24 BMW 1250 GS (OEM 100mm)
2024 Kove 450 Rally - with BRP Sub-mount (90mm)
2024 Kove 450 with OEM bar clamps (105mm)
GPR damper mount 100mm
GPR V5 Damper - 106mm
OEM bar clamp center-line spec is 90mm (All year KTMs & Husqvarna)
Confirm measurements for all aftermarket clamp options. It will not work with PDS/PDHS.
Verify measurements if running a steering damper, as some dampers alter OEM specs. Like certain GPR models, high-mounted dampers may not clear the top plate. See the picture below.
For unlisted bikes, measure the width of your handlebar top clamps center-to-center on the bolts (in millimeters).
Features:
Four different mounting positions
20mm slide adjustment for precise positioning
Compatible with all GPS mounts using the AMPS pattern
Center M6 for mounting an LED or similar accessory
Easily drill additional holes as needed
Limited Lifetime Warranty
Pre-Assembled Kit Includes:
Universal GPS Center Plate (anodized aluminum)
2x Billet Mounts (CNC aluminum)
Four M8 Bar Clamp Bolts
Speed nut plate
Spacer for Trail Tech Voyager Pro or any GPS with a wide dock (+2 inches)
Optional Tilt Wedge for an angled view ($15)
Note: Some high-mount dampers, such as older GPR models, are incompatible with the Stout Mount.
Fasst Company
Flexx Handlebars
By Fasst Company
The Flexx Handlebar provides the performance you need to eliminate numbness and hand fatigue, allowing you to enjoy each mile as much as the first.
There’s nothing like a backcountry adventure ride. It can be the most enjoyable miles you’ve ever ridden—until hand fatigue and numbness take over.
Flexx Handlebars minimize vibration through a proprietary bushing that isolates the handles from metal-to-metal contact, dramatically reducing hand numbness.
They also come with a variety of elastomers that allow you to tune the bar to your preferences. This provides you with the highest-performing handlebar available, combining less vibration, subdued impacts, and improved ergonomics for a better day on the bike.
Don’t let numbness and hand fatigue get in the way of your adventure.